Our website uses cookies. By continuing to use this site, you agree to our use of cookies in accordance with this notice and the Terms of Use.
Journals Monographies Textbooks Collections Authors
Submit manuscript
Bulletin of Bryansk state technical university

COMPUTER SOFTWARE FOR THE EVALUATION OF ECONOMIC MANAGEMENT OF INDUSTRIAL ENTERPRISE ON THE BASIS OF THE SIMULATION MODEL. Computer software for the evaluation of economic management of industrial enterprise on the basis of the simulation model.

Published in Bulletin of Bryansk state technical university · Volume 2014, Issue 1 · Pages 94–101 · Rubric: Computer engineering and information technology
DOI: https://doi.org/10.12737/23387
Received: 09.12.2016 Accepted: 09.12.2016 Published: 09.12.2016 Language of publication: RUS
Authors
AN
Anatoliy Yakimov
SPIN
ZA
Zakharchenkov Konstantin
ABSTRACT
The information assessments are developed to determine requirements to software-based simulation model. Software tools are designed to support decision-making control in the economic systems of enterprises. The software tools are focused on operation of simulation models by the makers managerial decisions.
KEYWORDS
simulation model, the economic system, industrial enterprise, information system.
Text References
Text
Text (PDF)
Read Download

1. Yakimov, A. I. Imitation modeling technology of control systems of the industrial enterprises: Monograph / A. I. Yakimov. - Mogilev: Belarusian-Russian University, 2010. - 304 p.

2. Shileyko, A. V. Introduction to the information theory of systems / A. V. Shileyko, V. F. Kochnev, F. F. Himushin; under the editorship of A. V. Shileyko. - M.: Radio and communication, 1985. - 280 p.

3. Yakimov, A. I. Iterative method of the distributed design organization of simulation models of complex systems / A. I. Yakimov // Information technologies and systems 2011 (ITS 2011): Proceedings of International Science Conf. (Minsk, October 26, 2011) / Editorial board: L. Yu. Shilin [etc.]. - Minsk: BSUIR, 2011. - pp. 220-221.

4. Gerasevich, V. A. Modern software for statistical processing of biomedical research / V. A. Gerasevich, A. R. Avetisov // Belarusian medical magazine. - 2005. - No. 1. - Access mode: http://miklebig.narod.ru/docum/statprog.htm.

5. Orlov, S. A. Technologies of software development: Textbook / S. A. Orlov. - SPb.: St. Petersburg, 2002. - 464 p.

6. Zgurovsky, M. Z. Foundations of system analysis / M. Z. Zgurovsky, N. D. Pankratova. - Kiev: BHV, 2007. - 544 p.

7. Yakimov, A. I. Software integration of simulation model with a complex information system / A. I. Yakimov, K. V. Zakharchenkov // Reports of BSUIR. - 2008. - No. 2(32). - pp. 111-117.

8. Maksimey, I. V. Imitation modeling on the computer / I. V. Maksimey. - M.: Radio and communication, 1988. - 232 p.

9. Troelsen, And. Pro C#2008 and the .NET 3.5 Platform Fourth Edition / And. Troelsen. - New York: Apress, 2007. - 726 p.

PDF JATS XML
The contact persons
Editor-in-Chief, editorial board chair
Editor-in-chief  of the journal  Bulletin of Bryansk State Technical University  KHANDOZHKO ALEKSANDER VLADIMIROVICH     Aleksander Vladimirovich Khandozhko is Doctor of Engineering (2002), Associate Professor (1993), Honorary Worker of Higher Professional Education of the Russian Federation, Professor of the Department of Metal-cutting Machines and Tools at Bryansk State Technical University (BSTU). He was born in Chelyabinsk in 1958. In 1980 he graduated from Bryansk Institute of Transport Engineering (BITE) (now - Bryansk State Technical University, BSTU) with a degree in Mechanical Engineering Technology, Metal-cutting Machines and Tools. From 1980 to 1983, he worked as a manufacturing engineer at an industrial enterprise. From 1983 until now he has been working at Bryansk State Technical University, having started his career at the university as a training master. In 1985 he entered the full-time postgraduate course in BITE. In 1989 he defended the thesis for the degree of Candidate of Science in the Dissertation Council of Moscow State Aviation Technological Institute (MSATI) on the specialty Heat Engines of Aircrafts. After defending his thesis, he worked as an assistant and then as an associate professor of the department of Metal-cutting Machines and Tools at BITE. In 2000 he entered the post-doctoral program and in 2002 he defended his doctoral thesis on the specialty of Technology and Equipment of Mechanical and Physical-technical Processing. After defending his thesis, he worked as a professor of the department until 2009. In 2009 he was appointed the head of the department of Metal-cutting Machines and Tools at Bryansk State Technical University. In 2016 when the laboratory of wave deformation and combined hardening in additive and subtractive technologies was founded at BSTU, he became the head of the department of modular technological equipment, continuing his teaching work as a professor of the department of Metal-cutting Machines and Tools. Khandozhko A.V. is a member of the editorial board of the journal Science Intensive Technologies in Mechanical Engineering (Bryansk). Since 2002 he has been a member of dissertation councils of several universities; currently he is a member of three dissertation councils D999. 155. 03, D999.112.02 and D212.021.03 aa well as being the Deputy Chairman of Dissertation Council D999.155.03.   Topics of scientific research 1. Fundamental theoretical and applied issues of designing cutting tools. 2. Theory and practice of designing and manufacturing process equipment, including for additive-subtractive processes. 3. Issues of mechanical processing of materials. 4. Problems of providing product quality in mechanical processing and additive processes.
5798
downloads
VAK Crossref RINC RINC Science Index Antiplagiat
© INFRA-M
Agreement Personal data protection and processing policy Support Powered by Editorum, 2026 Instructions
Login or Create
* Forgot your password?