UDK 621.95.025 Сверла. Сверла из инструментальных сталей
The article presents examples of practical application of descriptive geometry methods for solving engineering problems of determining and studying the parameters of the cutting part of a spiral drill. The necessity of graphical constructions is noted, which is due to the fact that it is impossible to measure the rear angle by a direct measurement method using a universal measuring instrument due to the complex geometric shape of the measuring object. The analysis of the geometric shape of the working part of the spiral drill, which includes the main rear conical surface of the drill tooth, the front screw surface of the drill groove, the cylindrical surface of the tooth back, the main and transverse cutting edges are presented. Using the double contact theorem, a projection of the tooth profile of a spiral drill is constructed on a plane parallel to the drill axis with a given profile projection on a plane perpendicular to the drill axis. The tooth profile is determined by the lines of intersection of the conical surface with the cylindrical surface and with the helical surface of the drill groove. The shape of the drill groove is considered to be set. Projections of the transverse cutting edge of the drill are constructed as lines of intersection of two conical surfaces with intersecting axes. The problem is solved using a bundle of auxiliary planes. The tendency of an increase in the angle of inclination of the transverse cutting edge to the drill axis with a decrease in the distance between the intersecting axes of conical surfaces is shown. Graphically, at an arbitrary point of the drill blade, the value of one of the main geometric parameters of the drill - the rear angle is determined. It is shown that the closer the point of the blade is to the center of the drill, the greater the value of the rear angle. The constructions are made in the 2D Compass-Graph design system. The paper used alternative methods for solving geometric problems, which, unlike traditional ones, provide a simpler and more visual graphical solution.
descriptive geometry, practical application, graphical drawings, intersection line, geometric parameters of the spiral drill.
1. Akinshev A.S., Klimentiev A.L., Gusarov A.M. Modelirovanie geometrii struzhechnyh kanavok spiralnyh sverl sredstvami Autodesk Inventor [Modeling of the geometry of chip grooves of spiral drills by means of Autodesk Inventor]. Tezisy dokladov 50 mezhdunarodnoy nauchno-tehnicheskoy konferentcii prepodavateley i studentov, posvyachennoy godu nauki [Abstracts of the 50th International Scientific and Technical Conference of Teachers and Students dedicated to the Year of Science. Vitebsk State Technological University]. Vitebsk. 2017, pp. 181. (in Russian)
2. Boykov A.A., Egiazaryan K.T., Efremov A.V., Kadykova N.S. Problemy geometro-graficheskoi podgotovki studentov vuzov [Problems of geometric-graphic training of university students]. Geometriya i grafika [Geometry and Graphics]. 2023, V. 11, I. 1, pp. 4-22. DOIhttps://doi.org/10.12737/2308-4898-2023-11-1-4-22. (in Russian)
3. Vyshnyepolskiy V.I., Kadykova N.S., Vereschagina T.A. Vserossiiskaya nauchno-metodicheskaya konferentsiya "Problemy inzhenernoi geometrii" i seminar "Geometriya i grafika" 2021 g [All-Russian scientific and methodological conference "Problens of engineering geometry" and the seminar "Geometry and graphics" 2021]. Geometriya i grafika [Geometry and Graphics]. 2022, V. 10, I. 2, pp. 35-52. DOIhttps://doi.org/10.12737/2308-4898-2022-10-2-35-52. (in Russian)
4. Vyshnyepolskiy V.I., Boykov A.A., Egiazaryan K.T., Kadykova N.S. Metodicheskaya sistema provedeniya zanyatii na kafedre "Inzhenernaya grafica" RTU MIREA [Metodological system for conducting classes at the department of "Engineering graphics" RTU MIREA]. Geometriya i grafika [Geometry and Graphics]. 2023, V. 11, I. 1, pp. 23-34. DOIhttps://doi.org/10.12737/2308-4898-2023-11-1-23-34. (in Russian)
5. Vyshnyepolskiy V.I., Boykov A.A., Efremov A.V., Kadykova N.S. Organizatsiya praktiko-orientirovannogo obucheniya na kafedre "Inzhenernaya grafica" RTU MIREA [Arrangement of practice-oriented learning at the department of "Engineering graphics" RTU MIREA]. Geometriya i grafika [Geometry and Graphics]. 2023, V. 11, I. 1, pp. 35-43. DOIhttps://doi.org/10.12737/2308-4898-2023-11-1-35-43. (in Russian)
6. Vyshnyepolskiy V.I., Boykov A.A., Egiazaryan K.T., Efremov A.V. Nauchno-issledovatelskaya rabota na kafedre "Inzhenernaya grafica" RTU MIREA [Scientific research at the department of "Engineering graphics" RTU MIREA]. Geometriya i grafika [Geometry and Graphics]. 2023, V. 11, I. 1, pp. 70-85. DOIhttps://doi.org/10.12737/2308-4898-2023-11-1-70-85. (in Russian)
7. Gavariev R.V., Khakimzyanova A.A. Ispolzovanie sredstv kompiuternogo modelirovaniya pri proektirovanii i izgotovlenii kontsevogo rezhuthego instrumenta [Se of computer modeling in the design and manufacture of the end of the cutting tool]. Naychyi vestnik [Scientific Bulletin]. 2016, I. 3(9), pp. 28-36. DOIhttps://doi.org/10.17117/nv.2016.03.028. (in Russian)
8. GOST 25751-83 Instrumenty rezhuthie. Terminy i opredeleniya obthih ponyatii. [State Standard 25751-83. Cutting tools. Terms and definitions of general concepts]. Moscow, Standartinform Rubl., 1990. 27 p. (in Russian)
9. Danilenko B.D. Sposoby zadaniya razmerov profilya struzhechnyh kanavok spiralnogo sverla na uchebnyh chertezhah [Methods to specify the chip groove profile dimensions of spiral drill on students draws]. Mashinostroitel [Machinebuilder], 2014, I. 11, pp. 17-20. (in Russian)
10. Dibner L.G., Shkurin Yu.P. Zatochka spiralinyh sverl [Sharpening of spiral drills], Moscow, Mashinostroenie Publ., 1967, 156 p. (in Russian)
11. Domnin P.V. Matematicheskoe modelirovanie vintovyh poverhnostei sverla v srede Mathcad [Mathematical modeling of drill screw surfaces in Mathcad]. Vestnik MGTU “Stankin” [Bulletin of MSTU "Stankin"], 2021, I. 1(56), pp. 106-110. (in Russian)
12. Zubkova O.S., Kuts V.V., Lykova L.N. Matematicheskoe predstavlenie rezhuthih kromok spiralnogo sverla v sisteme Maple [Mathematical representation of the cutting edges of a spiral drill in the Maple system]. Sovremennye materially, tehnika i tehnologii [Modern materials, equipment and technologies]. 2017, I. 7(15), pp. 21-28. (in Russian)
13. Ivanov G.S. Nachertatelnya geometriya [Descriptive geometry], Moscow, MGUL Publ., 2012, 224 p. (in Russian)
14. Leparov M.N. O geometrii, ethe odin raz [About geometry, one more time]. Geometriya i grafika [Geometry and Graphics]. 2022, V. 10, I. 1, pp. 3-13. DOIhttps://doi.org/10.12737/2308-4898-2022-10-1-3-13. (in Russian)
15. Malevsky N.P. Raschet i konstruirovanie spiralnyh sverl. Metodicheskoe posobie po kursu "Rezhuthii instrument" [Calculation and design of spiral drills. Methodical manual for the course "Cutting tools"]. Moscow, Rotaprint BMSTU, 1977, 54 p. (in Russian)
16. Malevsky N.P. Raschet profilya vintovyh kanavok spiralnyh sverl. Metodicheskoe posobie po kursu "Rezhuthii instrument" [Calculation of the profile of twist drill flutes. Methodical manual for the course "Cutting tools"]. Moscow, Rotaprint BMSTU, 1977, 16 p. (in Russian)
17. Malevskii N.P., Danilenko B.D. Podgotovka ishodnyh dannyh dlya graficheskogo opredeleniya profilya zuba diskovoi frezy dlya kanavki sverla v uchebnyh proektah po rezhuthemu instrument [Preparation of initial data for graphical determination of the tooth profile of a disc cutter for a drill groove in educational projects on cutting tools]. Izvestia vysshih uchebnyh zavedeniy. Mashinostroenie [News of higher educational institutions. Machinebuilding]. 2008, I. 1, pp. 79-82. (in Russian)
18. Malevskii N.P., Danilenko B.D. Profilirovanie struzhechnyh kanavok spiralnyh sverl [Profiling of chip grooves of spiral drills]. Vestnik Moskovskogo gosudarstvennogo universiteta im. N.E. Baumana. Seriya Mashinostroenie [Bulletin of the Bauman Moscow State Technical University. Mechanical Engineering Series]. 2009, I. 1(74), pp. 100-115. (in Russian)
19. Malevskii N.P., Danilenko B.D., Buloshnikov V.S. Profilirovanie struzhechnyh kanavok spiralnyh sverl i opredelenie profilya ih normalnogo secheniya [Profiling of chip grooves of spiral drills and determination of their normal cross-section profile]. Glavniy mechanic [The chief mechanic]. 2015, I. 5-6, pp. 36-40. (in Russian)
20. Martynenko K.F., Tikhonov D.A. Geometriya rezhuthei kromki spiralnogo sverla s obratnym uglom pri vershine [Geometry of spiral drill cutting edge with return corner at the top]. Vestnik Saratovskogo gosudarstvennogo universiteta [Bulletin of the Saratov State Technical University]. 2010, V. 3, I 1(46), pp. 46-49. (in Russian)
21. Oyuunzhargal Ch., Oyuunzayaa E. Tendentsii obucheniya v ingenernoi grafike [Trends of training in engineering graphics]. Geometriya i grafika [Geometry and Graphics]. 2022, V. 10, I. 2, pp. 35-59. DOIhttps://doi.org/10.12737/2308-4898-2022-10-2-53-59. (in Russian)
22. Petukhov Yu.E., Vodovozov A.A. Matematicheskaya model krivolineinoi kromki spiralnogo sverla povyshennoi stoikosti [Mathematical model of the curvilinear cutting edge of a durable helical bit]. Vestnik MGTU “Stankin” [Bulletin of MSTU "Stankin"]. 2012, I.3, pp. 28. (in Russian)
23. Pyatyh A.S. Matematicheskaya model geometrii rezhuthei chasti spiralnogo sverla [Mathematical model of the geometry of the cutting part of a spiral drill]. Aviamashinostroenie i transport Sibiri: sbornik statei IX Vserossiiskoi naychno-prakticheskoi konferentcii. Irkutskii natsionalnyi issledovalteskii universitet [Proc. 9th Russian Scientific and Practical Conference: Aircraft engineering and Transport of Siberia. Irkutsk National Research Technical University]. Irkutsk. 2017, pp. 232-236. (in Russian)
24. Sal'kov N.A. Osnovnye prichiny plohogo usvoeniya nachertatelnoi geometrii [The main reasons for poor assimilation of descriptive geometry]. Geometriya i grafika [Geometry and Graphics]. 2021, V. 9, I. 2, pp. 3-11. DOIhttps://doi.org/10.12737/2308-4898-2021-9-2-3-11. (in Russian)
25. Sal'kov N.A. Sistemnyi podhod k izucheniu nachertatelnoi geometrii [A systematic approach to the study of descriptive geometry]. Geometriya i grafika [Geometry and Graphics]. 2022, V. 10, I. 1, pp. 14-23. DOIhttps://doi.org/10.12737/2308-4898-2022-10-1-14-23. (in Russian)
26. Sal'kov N.A. Ob izobrazheniyah [About images]. Geometriya i grafika [Geometry and Graphics]. 2022, V. 10, I. 2, pp. 3-10. DOIhttps://doi.org/10.12737/2308-4898-2022-10-2-3-10. (in Russian)
27. Frolov S.A. Nachertatelnya geometriya [Descriptive geometry]. Moscow, Mashinostroenie Publ., 1983, 240 p. (in Russian)
28. Balandin A.D., Danilenko B.D. Producing helical channels on taps by means of face mills // Russian Engineering Research. 2013, V. 33, I. 6, pp. 355-357. DOIhttps://doi.org/10.3103/S1068798X1306004X.
29. Beju L.D., Brindasu D.R., Mutiu N.C., Rothmund J. Modeling, simulation and manufacturing of drill flutes // The International Journal of Advanced Manufacturing Technology. 2016, V. 83(9-12), I. 04, pp. 2111-2127. DOIhttps://doi.org/10.10007/S00170-015-7710-1.
30. Danilenko B.D., Malevskii N.P. Forming a helical chip-channel surface in a spiral drill by specifying two generative straight lines // Russian Engineering Research., 2009, V. 29, I. 4, pp. 397-399. DOIhttps://doi.org/10.3103/S1068798X09040157.
31. Ehrmann K.F., DeVries M.E. Grinding Wheel Profile Definition for the Manufacture of the Drill Flutes // CIRPAnnals. 1990, V. 39(1), pp. 153-156. DOIhttps://doi.org/10.1016/S0007-8506(07)61024-5.
32. Karpuschewski B., Jandecka K., Mourek D. Automatic search for wheel position in flute grinding of cutting tools // CIRPAnnals. 2011, V. 60(1), pp. 347-350 DOIhttps://doi.org/10.1016/j.cirp.2011.03.113.
33. Malkova L.D. Surface modeling as a tool for visualization and analysis of machining problems // AIP Conference Proceedings: International Scientific and Practical Conference "Modeling in Education 2019" - Moscow: American Institute of Physics Inc., 2019, V. 2195, pp. 020056. DOIhttps://doi.org/10.1063/1.5140156.
34. Malkova L.D. Residual relief analysis during milling process using surface modeling // AIP Conference Proceedings - Moscow, 2022, pp. 040009. DOIhttps://doi.org/10.1063/5.0074564.
35. Zhang S.Y., Liang Z.Q., Wang X.B., Zhou T.F., Jiao L., Yan P. Influence of Wheel Position Parameters of Flute Profile of Micro-Drill. Materials Science Forum. 2016, V. 874, I. 10, pp. 52-58. DOI:104028/www.scietific.net/MSF.874.52.
