employee
Lugansk, Luhansk People's Republic
BBK 344 Общее машиностроение. Машиноведение
The study objective is to find the possibility and expediency to introduce the method of control mathematical model into scientific research. The task to which the paper is devoted is to analyze the results of using a control model, with the help of which the reliability of calculations using mathematical models specially designed for a concrete scientific study is verified. The paper briefly reveals the essence of mathematical models developed and applied in scientific research using external, industry-specific regulatory and administrative documentation, as close as possible to the purpose of a mathematical model acting as a control, recheck according to one of the output parameters. The design and technological solutions presented in the study to improve the operational efficiency of gas turbine engines during factory repairs are confirmed by mathematical models, the development of which is required due to the lack of their analogues in scientific and technical information sources. The novelty of the research work is in the proposed methods for improving the efficiency of operation and repair of gas turbine engines, as well as in the application of the method of control mathematical model presented in the industry regulatory and administrative documentation. Taking into account the use of the developed mathematical models in the study, such a control model acts as an external check model of calculations. This article presents the results of positive application of the control mathematical model. Conclusions. In cases of developing new and previously unused computational and other mathematical models for a specific study, it is possible and advisable to use the method of a control mathematical model (models), which in such cases will act as an external one, borrowed from reliable information sources. The method of the control mathematical model can be applied in other studies if it is necessary to control the results of intermediate or final calculations when it is impossible to recheck them practically in the studied technical and other systems.
engine, blade, model, titanium nitride, repair
1. Zarubin VS, Markelov GE. Lectures on the basics of mathematical modeling: textbook. Moscow: Publishing House of the Bauman Moscow State Technical University; 2013.
2. Lyubchenko DI. Improving the efficiency of power plants by applying high-strength protective coatings to fastwearing parts [dissertation]. [Lugansk (RF)]: Lugansk State University; 2023.
3. Katz GB, Kovalev AP. Technical and economic analysis and optimization of machine design. Moscow: Machinostroenie; 1981.
4. Velikanova KM, editor. Calculations of the economic efficiency of new machinery: handbook. Leningrad: Machinostroenie; 1975.
5. Fedoseev VV, Garmash AN, Dayitbegov DM. Economic and mathematical methods and applied models: textbook for universities. Moscow: UNITY; 1999.
6. Chirkov VG. Calculations of the economic effect of new machinery. Kalinigrad: Technika; 1984.
7. Pankratov EL, Bulaeva EA, Boldyrevsky PB. Introduction to economic and mathematical modeling: textbook. Nizhny Novgorod: Nizhny Novgorod State University; 2017.
8. Lyubchenko DI, Bykadorov VV, Danileichenko AA. Problems of repairing compressor blades of gas turbine engines with protective coatings based on TiN. Vestnik Lugansk Vladimir Dahl State University. 2019;6(24):40-43.
9. Bykadorov VV, Danileichenko AA. Lyubchenko DI. On the problem of serial works on the application of protective nanocoatings to the resource-saving components of power plants of aviation and ground equipment. Transport Engineering. 2022;05(5):30-43. DOI:https://doi.org/10.30987/2782-5957-2022-5-30-43.
10. Potapov VI, Postnikov DV. How to perform scientific research, write, issue and defend a master's thesis: textbook. Omsk: Publishing House of OmSTU; 2013.
11. Zvonarev SV. Fundamentals of mathematical modeling: textbook.Ekaterinburg: Ural University Publishing House; 2019.
12. Lyubchenko DI, Bykadorov VV, Danileichenko AA. Determination of the effectiveness of aviation and ground equipment operation through mathematical simplification of influence factors. Vestnik Lugansk Vladimir Dahl State University. 2020;11(41):160-164.
13. Lyubchenko DI. Mathematical modeling of increased wear of gas turbine compressor blades. Scientific Conference of the Teaching Staff and Researchers Dedicated to the year of V. Dahl. Lugansk: University Science; 2021.
14. Pavlenko DV, Dvirnik YaV. Wear patterns of the compressor working blades of helicopter engines operating in a dusty atmosphere. Vestnik Dvigatelestroeniya. Production Technology and Repair. 2016;1:44-46.
15. GOST 16504-81 The state system of testing products. Product test and quality inspection. General terms and definitions. Moscow: Standartinform; 2011.
16. Vinogradov VN. Abrasive wear. Moscow: Machinostroenie; 1990.
17. Khvorostukhin LA, Nozhnitsky.YuA, Bolmanenkov AE. Study of the erosive strength of ion-plasma coating made of titanium nitride. Aviatsionnaya Promyshlennost. 1988;6:59-61.
18. Pavlenko DV, Dvirnik YaV. Wear patterns of the compressor working blades of helicopter engines operating in a dusty atmosphere. Vestnik Dvigatelestroeniya. Production Technology and Repair. 2016;1:43.
19. Lyubchenko DI, Bykadorov VV, Danileichenko AA. Determination of the cost recovery for increasing the wear resistance of compressor blades of gas turbine engines. Vestnik Lugansk Vladimir Dahl State University. 2022;7(61):37-40.
20. Lyubchenko DI, Bykadorov VV, Danileichenko AA. Determination of the cost recovery for increasing the wear resistance of compressor blades of gas turbine engines. Vestnik Lugansk Vladimir Dahl State University. 2022;7(61):37-40.
21. Methodology for determining the cost of repairing aircraft equipment depending on the time of its entry into the next repair. Moscow; 1989.
