employee
Ufa, Ufa, Russian Federation
employee
Ufa, Ufa, Russian Federation
employee
Ufa University of Science and Technology (Postgraduate Student)
graduate student
Ufa, Ufa, Russian Federation
employee
Ufa University of Science and Technology (Postgraduate Student)
graduate student
Ufa, Ufa, Russian Federation
UDC 665.765
Russian Library and Bibliographic Classification 35
The results of the development and laboratory tests of a new release lubricant are presented to facilitate the removal of concrete form and improve its surface quality. The influence of various oils and concentrations of functional additives on the surface quality of castings and the static friction from the formwork surface are found. The effectiveness of the release lubricant is determined by the quality of the concrete surface, the condition of formwork bottom and walls after concrete removal, by the physicochemical properties, and the static friction of the lubricated plate from the concrete surface. Also, during the development of a new release lubricant composition, the odor was evaluated organoleptically in comparison with the known release lubricants. The results of laboratory and pilot tests have shown that the developed release lubricant Rosoil-ZHBI provides a concrete surface at A1 level according to GOST 13015.0-83.
concrete, formwork, release lubricant, static friction
1. Federal State Statistics Service of the Russian Federation [Internet]. 2024 [cited 2024 May 20]. Available from: http://www.gks.ru
2. PromStroyKontakt Company. Lubricant for formwork. Main types. [Internet]. 2024 [cited 2024 May 21]. Available from: https://psk-holding.ru/about/stati/emulsol-smazka-dlya-opalubki
3. Shatov AN. Lubricants for molds and formwork: the right choice to increase competitiveness in construction. Concrete Technologies. 2013;9:12-15.
4. Bursov NG, Vorivodskaya NV, Dimitriadi NP, Ivashko LI., Obukhov AE. Problems and achievements of technology for the preparation and application of release lubricants for use in the production of concrete and reinforced concrete structures. Collection of Papers Based on the Materials of the International Scientific and Technical Conference Dedicated to the 100th Anniversary of the Birth of Akhverdov IN and Ataev SS, June 9-10, 2016: Innovations in Concrete Science, Construction Production and Engineering Personnel Training; Belarusian National Technical University. Minsk; 2016.
5. GOST 13015.0-83 Prefabricated concrete and reinforced concrete constructions and products. General technical requirements. Moscow: Izdatelstvo Standartov; 1984.
6. Galiakbirov AR, Rakhimov MN, Baulin OA. Development of release lubricant for concrete product molds. Bashkir Chemical Journal [Internet]. 2010;2 [cited 2024 Jul 10]. Available from: https://cyberleninka.ru/article/n/razrabotka-razdelitelnoy-smazki-dlya-form-betonnyh-izdeliy.
7. Khamzin IR. Release lubricant for formwork based on rapeseed oil. Issues of Science and Education. 2018; 6(18):7.
8. Galiakbirov AR. Development of release lubricants for forms of concrete products [abstract of dissertation]. [Ufa (RF)]; Ufa State Petroleum Technological University; 2011.
9. Abramov AN, Tyulenev DG, Sholom VYu, Puzyrkov DF. A set of test methods for lubricants used in metalworking processes. Proceedings of the XII All-Russian Congress on Fundamental Problems of Theoretical and Applied Mechanics. Ufa: RIC BASHGU; 2019.
10. Belov IB, Sholom VYu, Abramov AN. Lubricants of ROSOIL. Proceedings of the XII All-Russian Congress on Fundamental Problems of Theoretical and Applied Mechanics. Ufa: RIC BASHGU; 2019.
