Russian Federation
In the paper on the basis of nondimensional equations of motion of incompressible lubricant in a working gap and in porous layers of a bearing sleeve there is obtained a calculated model of a radial finite bearing with a double porous insert. A case is consi-dered when a permeability of porous layers on the boundary of gets one value. Lubricant is fed in a radial direction through a hole in a bearing body with subse-quent lubricant filtration through insert pores. As a result of the solution of the problem specified is obtained a field of rates and pressures in porous material and in a lubrication layer. There were determined analytical dependences for the constituents of a vector of a supporting force and a friction moment and also a load factor and a constant of friction were obtained. Besides, is defined a parameter characterizing a relative length of a porous constituent. It is proved that a rational running regime is achieved at the length of a porous constituent equal to 1/6 of a bearing length. The calculated specified models obtained allowed carrying out an analysis and comparison of theoretical results with experimental ones which defined a proximity of a new model to practice.
hydrodynamics, radial finite bearing, pressure, anisotropy, permeability, radial lubricant feed, con-stant of friction, load factor
1. Hydrodynamic computation of double layer porous infinite bearing taking into account permeability anisotropy of porous layer and inertia / К.S. Akhveriev, М.А. Mukutadze, V.S. Novgorodova, Т.S. Cherkasova // Bulletin of DSTU. - 2013. - № 5/6(74). - pp. 36-43.
2. Calculated model of double-layer porous finite bearing with account of porous layers anisotropy and nonlinear factors / А.Ch. Erkenov, М.А. Mukutadze, V.S. Novgorodova, Т.S. Cherkasova // Bulletin of DSTU. - 2014. - Vol. 14. -№ 1(76). - pp. 191-199.
3. Hydrodynamic computation of radial porous infinite bearing with increased loadcarrying capacity with account of inertia / М.А. Mukutadze, Е.Е. Alexandrova, А.А. Konstantinov, А.I. Shevchenko // Bulletin of RSUC. - 2012. - № 2(46). - pp. 194-197.
4. Sordge, F. Numerical method for computation of radial finite bearings lubricated with ferroliquid / F. Sordge // Friction Problems. - 1987. - № 1. - pp. 72-77.
5. Tolpinskaya, N.B. Porous Finite Bearing with Lu-bricant Feed through Insert Pores: Thesis for Can.Eng. Degree competition / N.B. Tolpinskaya. - Rostov-upon-Don, 1986. - pp. 20-40.
6. Zadorozhnaya, E.A. Solving a thermohydrodynamic lubrication problem for complexloaded sliding bearings with allowance for rheological behavior of lubricating fluid / E.A. Zadorozhnaya // Journal of Machinery Manufacture and Reliability. - 2015. - № 44(1). - Р. 46-56.
7. Rozhdestvensky, Y. A simulation of the thermal state of heavily loaded tribounits and its evaluation / Y. Rozhdestvensky, E. Zadorozhnaya // Bulletin of the South Ural State University, Series: Mathematical Modelling, Programming and Computer Software. - 2014. - № 7(4). - Р. 51-64.
8. Harnoy, A. Bearing Design in Machinery: Engineering Tribology and Lubrication / A. Harnoy. - New York : Marcel Dekker, 2003. - 440 p.
9. Cusano, C. Investigation of transfer ratio of resilient rolling bearing in damper with squeezed film and porous cage / C. Cusano, P.Е. Fank // Problems of Friction and Lubricant. - 1974. - № 1. - pp. 54.
10. Conry, C. On porous radial bearings stability / C. Conry, C. Cusano // Design & Engineering Tech-niques. - 1974. - № 2. - pp. 206-216.
